앱 다운로드Get the app
홈Home/보일러·온수기Boilers & Water Heaters/Unical/보일러·온수기Boilers & Water Heaters
Unical

Unical 보일러·온수기 에러코드 58개Unical Boilers & Water Heaters error codes (58)

Unical 보일러·온수기 화면에 뜨는 코드 58개의 뜻·긴급도·자가조치를 한 페이지에 모았습니다.All 58 Unical boilers & water heaters error codes — what each one means, how urgent it is and what you can do — on one page.

1즉시 정지Stop now
47AS 필요Service needed
2계속 사용 가능Keep using
8확인 필요Check needed

먼저 확인: 즉시 사용을 멈춰야 하는 코드 1개Check first: 1 code that means stop now

  • 20 가스밸브 누설 — 소화 후에도 화염이 감지됨Gas valve leaking — flame detected after switch-off

공통 조치 — 여러 코드에 같은 조치가 적용됩니다Shared steps — several codes share the same fix

① 코드 47개47 codes

전원을 껐다가 다시 켜 보세요. 코드가 다시 뜨면 공식 서비스센터에 점검을 요청하세요.Turn the appliance off and on again. If the code comes back, ask an authorized service center to inspect it.

② 코드 5개5 codes

전원을 껐다가 다시 켜 보세요. 증상이 계속되면 공식 서비스센터에 문의하세요.Turn the appliance off and on again. If the problem continues, contact an authorized service center.

③ 코드 2개2 codes

전원을 껐다가 다시 켜 보세요. 코드가 계속 반복되면 공식 서비스센터에 문의하세요.Turn the appliance off and on again. If the code keeps coming back, contact an authorized service center.

Unical 보일러·온수기 에러코드 전체 (58)All Unical boilers & water heaters codes (58)

리밋 서모스탯(안전서모 작동)SAFETY THERMOSTAT - Intervention of the safety thermostat (10)

보일러의 리셋 버튼을 누르세요. 그래도 코드가 남으면 공식 서비스센터에 점검을 요청하세요.Press the boiler's Reset button. If the code remains, contact an authorized service center.

확인 필요Check needed

점화 실패(가스없음/버너 미점화)BLOCK - No gas or failed burner ignition

가스가 공급되는지(가스밸브가 열려 있는지) 확인하세요. 그래도 점화되지 않으면 공식 서비스센터에 점검을 요청하세요.Check that the gas supply is on and the gas valve is open. If the boiler still fails to ignite, contact an authorized service center.

확인 필요Check needed

배기 안전(연도 klixon/응축수받이)Exhaust safety (flue klixon/condensate pan)

조치: 공통 조치 ②Fix: shared steps ②

확인 필요Check needed

과열(보일러 온도 과다)High Temperature - Boiler temperature too high

조치: 공통 조치 ②Fix: shared steps ②

확인 필요Check needed

저수압(수압 트랜스듀서 작동)Water Deficency - Insufficient water pressure and consequent intervention of the minimum water pressure - pressure switch (13).

난방 배관에 물을 보충해 수압을 약 1.2bar로 맞추고 값이 정상 범위로 돌아올 때까지 기다리세요. 그래도 코드가 남으면 공식 서비스센터에 점검을 요청하세요.Top the heating circuit up to about 1.2 bar and wait for the pressure to return to the normal range. If the code stays, ask an authorized service center to inspect it.

확인 필요Check needed

외기 온도센서 이상Outer Sensor

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

내부 고장(제어보드 내부 오류)Internal failure

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

예상 밖 화염(점화 전 감지=기생화염)Parasite Flame - Flame detected upon ignition

조치: 공통 조치 ②Fix: shared steps ②

확인 필요Check needed

공급(mandata) 온도센서 이상(난방)Heating Sensor (11) - Heating sensor fault

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

온수(sanitaria) 온도센서 이상Domestic Hot Water Sensor - Domestic hot water sensor fault (1)

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

환수(ritorno) 온도센서 이상(SRR 보조센서)Inlet temperature Sensor (SRR)

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

차동온도(1차 순환 부족 Δt>35°C)Water circulation insufficent - Primary circuit water circulation insufficient (Δt > 35° C)

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

열교환기 결빙 — 난방센서가 2°C 미만을 감지하면 버너 점화가 차단되고 5°C 초과까지 유지Exchanger freezing — burner ignition inhibited while heating sensor reads below 2C, until it reads above 5C

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

화염제어 주파수 한계 이탈 — 공급 전원의 주파수·전압이 규정 범위 밖Flame-control frequency out of limits — mains frequency/voltage outside standard range

조치: 공통 조치 ③Fix: shared steps ③

계속 사용 가능Keep using

점화·감지 전극이 버너에 접지되었거나 습기 존재Electrode shorted to burner ground, or moisture present

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

가스밸브 누설 — 소화 후에도 화염이 감지됨Gas valve leaking — flame detected after switch-off

가스 밸브를 잠그고 창문을 열어 환기하세요. 전기 스위치를 켜거나 끄지 마시고 불도 사용하지 마세요. 실외로 나온 뒤 가스공급업체나 공식 서비스센터에 연락하세요.Shut the gas valve and open the windows to ventilate. Do not switch anything electrical on or off, and keep all flames away. Go outside first, then call your gas supplier or an authorized service center.

즉시 정지Stop now

난방수 순환 부족Poor water circulation

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

센서 위치 오류 — 공급(mandata)·환수(ritorno) 센서가 서로 바뀜Sensors misplaced — flow and return sensors swapped

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

서비스 패널 버튼이 30초 넘게 눌린 상태로 감지됨Service-panel button detected pressed for more than 30 seconds

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

팬 속도 이상 — 요구 속도에 도달하지 못함(저속)Fan speed out of control — requested speed not reached (low speed)

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

배기가스 과열Exhaust smoke overheating

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

팬 속도 이상 — 요구 속도보다 빠름(고속)Fan speed out of control — speed higher than requested

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

공급온도 상승기울기 오류 — 순환펌프의 갑작스러운 정지 확인Flow temperature gradient error — check for sudden pump shutdowns

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed
2830, 38, 43

화염제어 주파수/전원(주파수·전압) 규정 이탈Scambiatore Ostruito

조치: 공통 조치 ②Fix: shared steps ②

확인 필요Check needed

설치(서비스) 파라미터 변조 — 전자기 간섭 등으로 값이 바뀜Service/installation parameters altered (possible electromagnetic interference)

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

시스템 구성값이 유효하지 않거나 손상됨System configuration invalid or corrupted

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

공급 전압 낮음(190Vac 미만이면 실제 저전압, 아니면 전압감시 회로 이상)Low line voltage (below 190 Vac = real undervoltage, otherwise line-monitor fault)

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

공장 파라미터 변조 — 전자기 간섭 등으로 값이 바뀜Factory parameters altered (possible electromagnetic interference)

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

점화 단계에서 약 50초 사이에 비정상 화염 소실이 12회 연속 발생12 consecutive abnormal flame losses during ignition within about 50 seconds

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed
4445, 53

전극 접지 단락/습기water sensor pressure - detected if the pressure Transducer is present

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

난방수 과압 — 압력 트랜스듀서 장착 시 2.5bar 초과에서 감지, 2bar 미만이면 자동 해제Water overpressure — detected above 2.5 bar with pressure transducer fitted; auto-resets below 2 bar

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

통신 오류Communication error

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

HCM·SHC 호스트 컨트롤러 없음HCM, SHC: host controller missing

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

룸1 온도센서 이상Room 1 temperature sensor

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

배기·응축수 배출 막힘 — 연도와 사이펀 확인Discharges obstructed — check flue and siphon

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

캘리브레이션 없음(taratura)No calibration (taratura)

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

호스트 컨트롤러 없음Host controller missing

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

버너가 감지되지 않음Burners NOT detected

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

전체 시스템 공급(플로우) 온도센서 이상Global flow temperature sensor

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

날짜·시각이 유효하지 않음Date and time not valid

조치: 공통 조치 ③Fix: shared steps ③

계속 사용 가능Keep using

SGV 액추에이터 이상Actuators SGV

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

캘리브레이션 미실시Missing calibration

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

온도센서 뒤바뀜Temperature sensors swapped

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

온도 상승기울기가 한계를 초과Temperature slope exceeds the limit

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed
8384, 85, 86

가스밸브 지령회로 문제Gas valve command circuit problem

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

가스밸브 개방 시간 초과Gas valve open time exceeded

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

최대 점화값 보정 후 화염 소실Flame lost after max ignition value calibration

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

화염 소실(점화 후 20초)Flame loss (20 seconds after ignition)

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed
9091, 92

변조(모듈레이션) 중 화염 소실 — 최소 출력 구간Flame loss during modulation (minimum power)

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

변조(모듈레이션) 중 화염 소실 — 중간 출력 구간Flame loss during modulation (medium power)

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

변조(모듈레이션) 중 화염 소실 — 최대 출력 구간Flame loss during modulation (maximum power)

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

가스밸브 배선 이상Gas valve wiring

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

화염 소실이 잦음Frequent loss of flame

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

미분류 이상 일반 잠금Internal error

조치: 공통 조치 ②Fix: shared steps ②

확인 필요Check needed

미분류 일반 잠금(락아웃)General lockout not listed

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

점화 실패Ignition failure

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

이온화(화염감지) 전극 단락Short circuit of the ionisation electrode

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

가스밸브 개방 지연Gas valve open delay

조치: 공통 조치 ①Fix: shared steps ①

AS 필요Service needed

제조사 공식 출처Official manufacturer sources

다른 브랜드 보일러·온수기Boilers & Water Heaters from other brands

⚠ 정보는 참고용입니다. 감전·가스·누수처럼 위험이 의심되면 즉시 사용을 멈추고 제조사 서비스센터에 문의하세요.⚠ For reference only. If you suspect a hazard such as shock, gas or a leak, stop using the appliance and contact the manufacturer's service center.