앱 다운로드Get the app
홈Home/세탁기·건조기Washers & Dryers/Philco/세탁기·건조기Washers & Dryers
Philco

Philco 세탁기·건조기 에러코드 18개Philco Washers & Dryers error codes (18)

Philco 세탁기·건조기 화면에 뜨는 코드 18개의 뜻·긴급도·자가조치를 한 페이지에 모았습니다.All 18 Philco washers & dryers error codes — what each one means, how urgent it is and what you can do — on one page.

13즉시 정지Stop now
1AS 필요Service needed
4계속 사용 가능Keep using

먼저 확인: 즉시 사용을 멈춰야 하는 코드 13개Check first: 13 codes that mean stop now

  • DE 건조 기판(PCI) 고장Drying control board (PCB) failure
  • E2 도어락 고장door lock failure
  • E3 배수 불량drain fault
  • E4 넘침overflow
  • E5 드럼 속도 불일치(모터 고착/기판)drum speed mismatch (motor seized/control board)
  • E6 물 가열 실패(센서)water heating failure (sensor)
  • E7 가열센서 고장heating sensor failure
  • E9 통신 오류(메인+인버터 기판)communication error (main + inverter board)
  • E10 인버터 기판 고장inverter board failure
  • FE 건조 모터 고장drying motor failure
  • IE 덕트 입기센서duct air inlet sensor
  • OE 덕트 출기센서duct air outlet sensor
  • UNB 세탁조 언밸런스(세탁물 쏠림) — 세탁물 재배치 후 재시작Basket unbalanced load — redistribute laundry and restart

공통 조치 — 여러 코드에 같은 조치가 적용됩니다Shared steps — several codes share the same fix

① 코드 11개11 codes

지금 바로 사용을 멈추고 전원을 차단하세요. 직접 분해하거나 수리하지 마시고, 공식 서비스센터에 점검을 요청하세요.Stop using the appliance now and cut the power. Do not open it up or repair it yourself — ask an authorized service center to inspect it.

Philco 세탁기·건조기 에러코드 전체 (18)All Philco washers & dryers codes (18)

도어 개방을 위한 배수 대기(정상 동작)Waiting for drainage before the door can be opened (normal state)

세탁물을 고르게 다시 배치한 뒤 다시 시작하세요.Redistribute the laundry evenly, then restart the cycle.

계속 사용 가능Keep using

건조 기판(PCI) 고장Drying control board (PCB) failure

조치: 공통 조치 ①Fix: shared steps ①

즉시 정지Stop now

급수 불량water supply fault

수도꼭지가 열려 있는지, 급수호스가 꺾이지 않았는지 확인하고 급수필터를 점검하세요. 그래도 코드가 남으면 공식 서비스센터에 점검을 요청하세요.Check that the tap is open and the supply hose is not kinked, and check the water inlet filter. If the code remains, contact an authorized service center.

계속 사용 가능Keep using

도어락 고장door lock failure

조치: 공통 조치 ①Fix: shared steps ①

즉시 정지Stop now

배수 불량drain fault

배수 필터의 이물질을 제거하세요.Remove debris from the drain filter.

즉시 정지Stop now

넘침overflow

배수 호스가 규정 위치(50~100cm)에 설치됐는지 확인하세요. 그래도 코드가 남으면 공식 서비스센터에 점검을 요청하세요.Check that the drain hose is at the correct position (50-100 cm). If the code remains, contact an authorized service center.

즉시 정지Stop now

드럼 속도 불일치(모터 고착/기판)drum speed mismatch (motor seized/control board)

조치: 공통 조치 ①Fix: shared steps ①

즉시 정지Stop now

물 가열 실패(센서)water heating failure (sensor)

조치: 공통 조치 ①Fix: shared steps ①

즉시 정지Stop now

가열센서 고장heating sensor failure

조치: 공통 조치 ①Fix: shared steps ①

즉시 정지Stop now

통신 오류(메인+인버터 기판)communication error (main + inverter board)

조치: 공통 조치 ①Fix: shared steps ①

즉시 정지Stop now

인버터 기판 고장inverter board failure

조치: 공통 조치 ①Fix: shared steps ①

즉시 정지Stop now

노브 위치가 시작된 사이클과 다름 — 노브를 사이클 위치로 되돌리고 재시작Knob position differs from the cycle that was started — return the knob and restart the cycle

노브를 원래 사이클 위치로 되돌리고, 기기가 식을 때까지 기다리세요.Turn the knob back to the cycle position and wait for the appliance to cool down.

계속 사용 가능Keep using

건조 모터 고장drying motor failure

조치: 공통 조치 ①Fix: shared steps ①

즉시 정지Stop now

건조 덕트 고장(건조 모터 축 고착)Drying duct failure (drying motor shaft seized)

전원을 껐다가 다시 켜 보세요. 코드가 다시 뜨면 공식 서비스센터에 점검을 요청하세요.Turn the appliance off and on again. If the code comes back, ask an authorized service center to inspect it.

AS 필요Service needed

덕트 입기센서duct air inlet sensor

조치: 공통 조치 ①Fix: shared steps ①

즉시 정지Stop now

덕트 출기센서duct air outlet sensor

조치: 공통 조치 ①Fix: shared steps ①

즉시 정지Stop now

드럼(세탁조) 내부 냉각 대기(정상 동작)Waiting for the drum interior to cool down (normal state)

배수와 잠금 해제가 끝날 때까지 기다리세요.Wait until the appliance finishes draining and unlocks.

계속 사용 가능Keep using

세탁조 언밸런스(세탁물 쏠림) — 세탁물 재배치 후 재시작Basket unbalanced load — redistribute laundry and restart

조치: 공통 조치 ①Fix: shared steps ①

즉시 정지Stop now

제조사 공식 출처Official manufacturer sources

다른 브랜드 세탁기·건조기Washers & Dryers from other brands

⚠ 정보는 참고용입니다. 감전·가스·누수처럼 위험이 의심되면 즉시 사용을 멈추고 제조사 서비스센터에 문의하세요.⚠ For reference only. If you suspect a hazard such as shock, gas or a leak, stop using the appliance and contact the manufacturer's service center.