LG 세탁기·건조기 에러코드 46개LG Washers & Dryers error codes (46)
LG 세탁기·건조기 화면에 뜨는 코드 46개의 뜻·긴급도·자가조치를 한 페이지에 모았습니다.All 46 LG washers & dryers error codes — what each one means, how urgent it is and what you can do — on one page.
먼저 확인: 즉시 사용을 멈춰야 하는 코드 2개Check first: 2 codes that mean stop now
공통 조치 — 여러 코드에 같은 조치가 적용됩니다Shared steps — several codes share the same fix
① 코드 3개3 codes
전원을 껐다가 다시 켜 보세요. 코드가 다시 뜨면 공식 서비스센터에 점검을 요청하세요.Turn the appliance off and on again. If the code comes back, ask an authorized service center to inspect it.
② 코드 3개3 codes
전원을 껐다가 다시 켜 보세요. 코드가 계속 반복되면 공식 서비스센터에 문의하세요.Turn the appliance off and on again. If the code keeps coming back, contact an authorized service center.
③ 코드 2개2 codes
전원을 끄고 10초 기다린 뒤 다시 켜고 코스를 처음부터 실행하세요. 그래도 코드가 남으면 공식 서비스센터에 점검을 요청하세요.Turn the power off, wait 10 seconds, turn it back on, and restart the cycle. If the code remains, contact an authorized service center.
④ 코드 2개2 codes
전원 플러그를 60초간 뽑았다가 다시 꽂고 재시작하세요. 그래도 코드가 남으면 공식 서비스센터에 점검을 요청하세요.Unplug the appliance for 60 seconds, then plug it back in and restart. If the code persists, contact an authorized service center.
LG 세탁기·건조기 에러코드 전체 (46)All LG washers & dryers codes (46)
스팀 급수 오류Steam water supply error
스팀 급수함에 MAX선까지 물을 채우고 서랍을 닫으세요.Fill the steam water box up to the MAX line and close the drawer.
쿨다운(오류 아님, 행정 종료)The drying cycle is completed (cool down).
세탁물을 꺼내거나 시작/일시정지 버튼을 누르세요.Remove the laundry or press the START/PAUSE button.
건조 후 구김방지·냉각팬 동작Cool down cycle active — the drying cycle has completed.
고장이 아닙니다. 빨래를 꺼내거나 버튼을 눌러 동작을 해제하세요. 그대로 기다리셔도 됩니다.This is not a fault. Remove the laundry or press a button to stop it. You can also simply wait.
드럼 3분 내 20RPM 미달(회전 불가)Over-current in the electrical circuit / motor.
전원 플러그를 10초간 뽑았다가 다시 꽂으세요. 그래도 코드가 남으면 수도꼭지를 잠그고 공식 서비스센터에 점검을 요청하세요.Unplug the appliance for 10 seconds, then plug it back in. If the code remains, close the water tap and contact an authorized service center.
차일드 락(오류 아님)The child lock feature is active.
차일드 락 버튼을 3초 이상 길게 눌러 잠금을 해제하세요. 버튼 위치는 모델에 따라 다를 수 있습니다.Press and hold the child lock button for 3 seconds to turn the lock off. The button may differ depending on the model.
배기덕트 막힘 75% (d80/d90/d95 는 각각 80/90/95%)Exhaust duct clogged 75% (d80/d90/d95 mean 80/90/95%)
린트 필터와 배기 호스, 외부 배기구가 막히지 않았는지 확인하고 청소하세요.Check the lint filter, the exhaust hose, and the outside vent for clogs, and clean them.
도어(서랍) 잠금 오류The washer is unable to lock the door.
문(서랍)을 끝까지 확실히 닫고 START/PAUSE 버튼을 누르세요. 그래도 코드가 남으면 전원을 껐다가 문을 확실히 닫고 다시 시작하세요.Close the door (drawer) firmly and press START/PAUSE. If the code remains, turn the power off, close the door firmly, and start again.
도어 안 닫힘·안 잠김The door is not closed properly.
문을 열었다가 중앙을 눌러 완전히 다시 닫으세요. 전원 플러그를 뽑은 뒤 시작 버튼을 5초간 눌러 리셋하세요. 그래도 코드가 남으면 공식 서비스센터에 점검을 요청하세요.Open the door and close it again firmly, pressing on the center. Unplug the unit and hold START for 5 seconds to reset. If the code remains, contact an authorized service center.
리드 미체결Lid not latched
걸쇠 주변의 이물질을 제거한 뒤 리드와 서랍을 완전히 닫으세요.Clear any debris around the latch, then close the lid and the drawer fully.
건조(드라이) 기능 일시 오류 — 전원 리셋 후에도 지속되면 서비스 필요Temporary dry-function error - if it persists after a power reset the unit needs service
조치: 공통 조치 ①Fix: shared steps ①
건조겸용 세탁기 건조 팬모터 불량Temporary dry function error.
전원을 끄고 10초 기다린 뒤 다시 켜서 코스를 재시작하세요. 그래도 코드가 남으면 공식 서비스센터에 점검을 요청하세요.Switch the power off, wait 10 seconds, then turn it back on and restart the cycle. If the code remains, contact an authorized service center.
도어 래치 스위치 오작동The door latch switch is not functioning.
끼인 물건이 있으면 제거하고, 전원 플러그를 10초 동안 뽑았다가 다시 꽂은 뒤 재시작하세요.Remove any items that are caught, then unplug the appliance for 10 seconds and restart it.
자동 배수(오류 아님)The unit timed out and is auto-draining. This is not an error — it is an automatic protective action.
조치: 공통 조치 ②Fix: shared steps ②
스팀 급수 문제Dryer: problem with the water supply used for the steam cycle.
수도꼭지가 얼거나 막히지 않았는지 확인하세요. 급수호스 상태를 살펴보고 급수필터를 청소하세요.Check that the tap is not frozen or clogged. Inspect the inlet hose and clean the inlet filter.
클러치 오류(펄세이터-통 사이 이물)Clutch error — a foreign object is stuck.
통 안의 세탁물을 모두 꺼내고, 통과 펄세이터 틈새에 동전이나 지퍼 같은 이물질이 끼어 있는지 확인해 제거하세요.Remove all items from the tub and check the seam for trapped objects such as coins or zippers.
설치 오류(프론트 세탁기 아래 미정렬)Installation error (not aligned under the front-load washer)
조치: 공통 조치 ②Fix: shared steps ②
배수호스 꺾임/막힘(응축식 한정)Dryer: the drain hose is kinked, crushed, clogged, or the water in the sump is frozen.
호스가 손상되거나 막히지 않았는지 확인하세요. 정품 호스만 사용하고 다시 시작하세요.Check the hose for damage and clogs. Use only the manufacturer's standard hose, then restart.
배수펌프 오류Unable to drain water.
배수 호스가 꺾이거나 막히지 않았는지 확인하고, 배수펌프 필터를 청소하세요.Check the drain hose for kinks or clogs and clean the drain pump filter.
린트필터 미삽입Lint filter not inserted
린트 필터를 뺐다가 다시 끼우세요.Remove the lint filter and reinsert it.
과급수·거품 과다·필터 막힘The washer is overfilling.
드럼 전용 세제를 적정량만 사용하고 배수 필터를 청소하세요. 수도꼭지를 잠그고 물을 배수한 뒤 다시 시작하세요.Use the right amount of detergent for drum washers and clean the drain filter. Close the water taps, drain the washer, then restart the cycle.
동결(급수·배수호스·수도꼭지 얼음)Freeze failure — the unit is frozen.
세탁통에 50~60℃ 정도의 따뜻한 물을 붓고 1~2시간 두어 얼음을 녹이세요. 급수·배수 호스도 함께 녹이세요. 남은 물은 빼내어 다시 얼지 않도록 하세요.Pour warm water (50-60°C) into the tub and leave it for 1-2 hours to thaw the ice. Thaw the inlet and drain hoses as well. Drain the remaining water so it does not freeze again.
가스 공급 없음(가스식)Dryer: the dryer is not receiving gas.
가스 공급 밸브가 열려 있는지, 가스 호스가 꺾이지 않았는지 확인하세요. 정상적으로 연결되어 있는데도 코드가 남으면 공식 서비스센터에 점검을 요청하세요.Check that the gas supply valve is ON and the gas line is not kinked. If it is connected properly and the code remains, contact an authorized service center.
습도센서 오류Dryer: error with the humidity sensor.
린트 필터 아래에 있는 센서를 물걸레로 닦은 뒤 완전히 말리세요. 증상이 계속되면 공식 서비스센터에 점검을 요청하세요.Wipe the sensors below the lint filter with a damp cloth and let them dry completely. If it persists, contact an authorized service center.
급수 부족(수도 잠김·호스 꺾임·필터 막힘·저수압)The water supply is inadequate.
수도꼭지가 완전히 열려 있는지 확인하세요. 급수호스가 꺾였으면 펴고 급수필터를 청소하세요.Make sure the tap is fully open. Straighten a kinked supply hose and clean the water inlet filter.
모터 과부하·구속(과다세탁물·이물질)The motor is overloaded and locked / the tub will not spin.
전원을 끄고 30분 정도 그대로 두세요. 세탁물 양을 줄이고 세탁통 틈새의 이물질을 제거한 뒤 다시 시작하세요.Leave the appliance switched off for 30 minutes. Reduce the load, remove any foreign objects from the tub, then restart the cycle.
세제함(슬라이드) 열림The detergent drawer is not fully inserted.
세제함을 끝까지 밀어 넣어 완전히 닫으세요.Make sure the detergent drawer is inserted all the way.
Wi-Fi 모듈 연결 오류Connection issue between the control panel and the Wi-Fi module.
조치: 공통 조치 ④Fix: shared steps ④
히터 무전류(전원 이상)Dryer: no current is being detected at the heater.
전원 코드가 제대로 꽂혀 있는지 확인하고 차단기를 리셋한 뒤 콘센트 상태를 확인하세요. 그래도 코드가 남으면 공식 서비스센터에 점검을 요청하세요.Check the power cord, reset the circuit breaker and check the outlet. If the code stays, ask an authorized service center to inspect it.
배수 안 됨(호스 꺾임·필터 막힘)The water cannot drain.
배수 필터를 청소하고, 배수 호스가 꺾이거나 막히지 않았는지 확인하세요. 하수구가 막히지 않았는지도 확인하세요.Clean the drain filter and check the drain hose for kinks or clogs. Also check that the household drain is not blocked.
수위감지센서 이상The water level sensor is malfunctioning.
조치: 공통 조치 ⑤Fix: shared steps ⑤
정전(행정 중 전원 끊김)A power failure occurred.
전원을 분리한 상태에서 시작/일시정지 버튼을 5초간 누른 뒤, 전원을 다시 연결하고 재시작하세요.With the power disconnected, hold the Start/Pause button for 5 seconds, then restore power and restart.
전압 부적합/배선 반대Power supply issue / improper voltage with the power cord.
전원 코드를 멀티탭이 아닌 벽 콘센트에 직접 꽂으세요. 전원을 뽑고 60초 기다렸다가 다시 연결해 재시작하고, 필요하면 차단기를 리셋하세요. 그래도 코드가 남으면 공식 서비스센터에 점검을 요청하세요.Plug the power cord directly into a wall outlet instead of a power strip. Unplug it, wait 60 seconds, plug it back in and restart, and reset the circuit breaker if needed. If the code persists, contact an authorized service center.
거품 과다Too many suds detected.
세제를 제조사 권장량 이하로 줄여 사용하세요.Reduce the amount of detergent to the manufacturer's recommended level.
통세척 동작 중It is time to run the Tub Clean cycle.
한 달에 한 번 통세척 코스로 세탁조를 청소하세요. 전용 세탁조 세정제를 사용하세요.Run the Tub Clean cycle once a month. Use a washing machine tub cleaner.
온도감지센서 이상·과열수 투입Heating error / faulty thermistor.
뜨거운 물을 넣었다면 전원 플러그를 뽑고 기기가 식은 뒤 다시 시작하세요. 그래도 코드가 남으면 공식 서비스센터에 점검을 요청하세요.If hot water was added, unplug the machine, let it cool down, and restart. If the code remains, contact an authorized service center.
서미스터 문제Thermistor problem
전원을 뽑은 뒤 시작/일시정지 버튼을 5초간 눌러 리셋하세요.Unplug the appliance and hold the Start/Pause button for 5 seconds to reset it.
저온 조건 서미스터 오류Dryer: a problem was detected with the dryer's thermistor (typically in cold conditions).
린트 필터를 청소하고 배기구가 막히거나 얼지 않았는지 확인하세요. 증상이 계속되면 공식 서비스센터에 점검을 요청하세요.Clean the lint filter and check the vents for clogs or frost. If it persists, contact an authorized service center.
서미스터 온도 범위 초과Thermistor temperature out of range
조치: 공통 조치 ①Fix: shared steps ①
탈수 불균형(세탁물 쏠림·수평 불량)The laundry is unbalanced.
세탁물을 고르게 다시 배치하세요. 양이 적을 때는 비슷한 옷을 더 넣고, 세탁물은 드럼 용량의 약 3분의 2를 넘지 않게 하세요. 세탁기가 수평으로 놓였는지도 확인하세요.Rearrange the load evenly. Add similar items to small loads and keep the load to about two-thirds of the drum capacity. Also make sure the washer is level.
진동감지센서 접촉불량·이상Vibration sensor issue.
시작/일시정지 버튼을 다시 누르고 전원을 껐다가 다시 켜세요. 같은 코드가 반복되면 공식 서비스센터에 점검을 요청하세요.Press Start/Pause and restart the appliance. If it happens again, contact an authorized service center.
LG의 다른 제품군Other LG categories
다른 브랜드 세탁기·건조기Washers & Dryers from other brands
⚠ 정보는 참고용입니다. 감전·가스·누수처럼 위험이 의심되면 즉시 사용을 멈추고 제조사 서비스센터에 문의하세요.⚠ For reference only. If you suspect a hazard such as shock, gas or a leak, stop using the appliance and contact the manufacturer's service center.